Bath Re-enameling Contractors in Durban

Contractorfind.co.za is proud to showcase only the best, registered and certified Bath Re-enameling Contractors in Durban. Need qualified Bath Re-enameling Contractors for the job? Contractorfind.co.za is the place to find them!

All the listed Bath Re-enameling Contractors below have been screened and certified, ensuring that their service and quality is the best in Durban. Find a Top Bath Re-enameling Contractors in Durban now.

Don’t waste your time with inadequate service providers… allow us to provide you the best professional people for the job!

READ MORE ABOUT Bath Re-enameling Contractors IN Durban :

Why re-enamel?
Even the simplest of bathrooms puts focus on a bath and it has to be stunning, perfect and gleaming in order to achieve your objective. Reclamation projects abound as more and more people are recognising the value in what was once considered old or outdated. But unfortunately many of these proud old baths are in such disrepair that they get overlooked for something shiny and new. If you are lucky enough to find an original cast iron bath at a great price, dont let it slip through your fingers. Grab it and then have it re-enamelled, re-glazed or re-coated, any colour you want too.

Of course the easier option is to buy new, but the prices of enamel baths today often makes these beauties out of reach of the average person and this is why re-surfacing a tired old standard is a fantastic option for any homeowner.
Bath recoat options
A bathtub is much more than a place in which you clean yourself, it is a place where you kick back, hide away and ebb away stress and sore muscles. If your bathtub is scratched, cracked or even stained youll probably head straight for the shower!

There are various ways to get a bright gleaming, stain free and perfectly smooth bathtub, the first is to replace it. Just rip it out and replace. But remember you could be in for quite a shock, not only from a cost point of view but consider the days or weeks you will have to put up with contractors in and out of your home. Youll probably have to rip out some of the flooring too as well as wall tiles, and we wont even mention the plumbing bill!

Or, you could simply re-glaze your bath. It costs the least, imposes no potential damages to your existing structure and wont take more a few days to complete. When its done you wont even know there ever was a nasty looking tub there before. The process of re-enamelling first takes care of whatever cracks or chips are already there and then the complete surface is re-coated, leaving you with a strong and shiny finish that looks brand new. Plus your tub, flooring, tiles and taps stay in place during the process. How good is that?

Re-enamelling a bath has great benefits in terms of cost, time and durability, but (and there is a but) if it isnt done right you may be left with cracks that can lead to holes which can lead to leaks and mould. So do yourself a favour, use a professional, unless you know are confident that you know what you are doing.
Going the DIY Route
Naturally, not everyone is a complete ignoramus when it comes to re-glazing a bathtub and many homeowners can pull this type of DIY project off and they have at their disposal many great DIY kits.

Re-coating a bathtub involves chemicals so make sure that you and your family are safe during the process. Make sure the area is well ventilated and that you are well protected with a ventilator, goggles and gloves.

Clean the tub first and remove any loose caulking and/or gaskets. Many kits offer a chemical cleaning solution which you must use in order to remove any soapy or oily residue off the surface.

The second cleaning solution is applied next with specially designed pads that score and roughen up the surface a little, ready to hold the primer. Rinse the tub afterwards and allow it to dry thoroughly.

The next step in the process would be to use the solvent supplied to further remove any residue. Once applied, you can then attend to any damage on the surface. Using putty, fill in cracks or holes and sandpaper smooth with a fine grit. Once dry you can get busy masking the areas around the tub that will be re-coated, making sure that you have a good seal.

Now its time to apply the cast coat. Follow the manufacturers directions for mixing and apply with a spray gun for the best result. Allow to dry and then apply the top coat in even strokes, again using a spray gun. This topcoat will take about two to three days to cure, but if done correctly your re-enamelling project will cost you dramatically less.
Choosing the right company
The DIY route being said and done, most of us cannot see our way to completing such a complex project on our own, and this gives rise to the question who do you choose to do your re-glazing?. You want to find someone who wants to do your job because they like what they are doing, not because they have to. Find someone who is interested in your bathroom plans, who ask you questions about it. Someone offhand on the telephone is possibly not your best option. They should be able to immediately answer any questions you have in a way that makes sense to you.

Ask them about techniques, about guarantees, about time and expense. Check out whether they have different options in re-enamel and do they offer various colours.

Having never had your bath re-coated before there will be many questions you simply arent primed to ask, dont worry, a good contractor will be able to talk you through the process, costs and time without faltering. They should be able to explain their materials in a way that makes sense to you and should never be pushy or come across as being impatient. In a nutshell, they should know their business!